Manifolds - BN4 from engine no. 48863 and all BN6 to BJ8 with twin carburettors
short, inlet manifold to cylinder head
BN4, BN6 to 66673
Required: 7
short, inlet manifold to cylinder head
BN4, BN6 to 66673
Required: 6
short, inlet manifold to cylinder head
BN4, BN6 to 66673
Required: 5
long, inlet manifold to cylinder head
BN6 from 66673, BN7 and BT7
Required: 1
long, inlet manifold to cylinder head
BN6 from 66673, BN7 and BT7
Required: 2
for thermo capillary tube
BN6 from 66673, BN7, BT7, BJ7 and BJ8
Required: 1
exhaust manifold - supplied in sets of two
BN4 to engine no. 48862 (1956-57)
Required: 1
BN4 from engine no. 48863 on, all BN6, BN7, BT7, BJ7 and BJ8 (1957-68)
Required: 1
used item
BN4 from engine no. 48863 plus all BN6 (1957-59)
Required: 1
used item
BJ7
Required: 1
for brake servo connection
BN4 from 48863, BN6, BN7 and BT7
Required: 1
for vacuum take off
BN4 from 48863, BN6, BN7, BT7 and BJ7
Required: 1
carburettor to inlet manifold
BN4 from 48863, BN6, BN7 and BT7
Required: 8
Required: 2
drain pipe
Required: 2
for overflow pipe
BN4 from 56201, BN6 to BJ8
Required: 1
BN4 from 56201, BN6 to BJ8
Required: 1
for twin SU-HD6 and HS6 carburettors
BN4 from engine no. 48863, all BN6 plus BN7 and BT7 MkI models to engine no. 29D-26212 (1957-61) • BJ7 (1962-63)
Required: 1
between carburettor and inlet manifold - 7 mm deep
BN4 from engine no. 48863, all BN6 plus BN7 and BT7 MkI models to engine no. 29D-26212 (1957-61)
Required: 2
carburettor to inlet manifold - 19/32" deep and 1.3/4" inner diameter
BJ7 (1962-63)
Required: 2
carburettor to inlet manifold - OE specification with 12 mm depth
BJ8 (1963-68)
Required: 2
carburettor to inlet manifold - 6 mm deep. May replace original 12 mm spacer, you will use two as much as original to fit
BJ8 (1963-68)
Required: 4
between carburettor and inlet manifold - 1.3/4" inner diameter
100M (1955) • BN4 from engine no. 48863, all BN6 plus BN7 and BT7 MkI models to engine no. 29D-26212 (1957-61) • BJ7 (1962-63)
Required: 2
between carburettor and inlet manifold - 2" inner diameter
BJ8 (1963-68)
Required: 4
front - used item
BN4 from engine no. 48863 and all BN6 (1957-59)
Required: 1
front - used item
BN7, BT7, BJ7 and BJ8
Required: 1
rear - used item
BN4 from engine no. 48863 and all BN6 (1957-59)
Required: 1
rear - used item
BN7, BT7, BJ7 and BJ8
Required: 1
for twin and triple SU carburettors - mild steel. Please note: on BN4 to BJ7 cars the LH front outrigger needs some modification
BN4 to BJ8
Required: 1
roll with 10 meter - 50 mm wide, 2 mm thick. Heat resistant to 1000° C
Required: 1
Content: 10 m (€7.90 / 1 m)
black matt
Suitable for manifolds and exhaust systems
Required: 1
Content: 400 ml (€29.75 / 1000 ml)
red matt
Suitable for manifolds and exhaust systems
Required: 1
Content: 310 ml (€80.65 / 1000 ml)
