Internal electrics - horn, relays and switches
starter motor. ST2 type with push button
Alternatives
Required: 1
2 fuse variant with 5 screw-in terminals. SF6 type without cover
TR2 and TR3, TR3A to TS60000
Required: 1
reproduction of the Lucas 4FJ type for 2 fuses - variant with lucar terminals
TR3A from TS60001 plus all TR3B, TR4 and TR4A (1959-67)
Required: 1
4FJ type for 2 fuses - variant with lucar terminals
TR3A from TS60001 plus all TR3B, TR4 and TR4A (1959-67)
Required: 1
for Lucas 4FJ fuse box
TR3A from TS60001 plus all TR3B, TR4 and TR4A (1959-67)
Required: 1
35 Ampere with 32 mm overall length and 6.2 mm diameter. Glass type
50 Ampere with 32 mm overall length and 6.2 mm diameter. Glass type
for C39 and C40 dynamo. RB106 type with 5 screw-in terminals
TR2 and TR3, TR3A to TS60000
Required: 1
for C40 dynamo - with lucar terminals, type: RB603
TR3A from TS60001, TR3B, TR4 and TR4A
Required: 1
replica of the FL5 flasher relay with 3 screw-in terminals and round housing
Alternatives
Required: 1
replica of the FL5 flasher relay with 3 Lucar terminals and round housing
Required: 1
FL5 flasher relay with 3 terminals and round housing
Required: 1
low note - alloy cast horn with domed cover. 12 volt with 2 wire terminals
TR2, TR3, TR3A and TR3B
Required: 1
high note - alloy cast horn with domed cover. 12 volt with 2 wire terminals
TR2, TR3, TR3A and TR3B
Required: 1
for original horn - new item
TR2, TR3, TR3A and TR3B
Required: 2
for original horn - used item
TR2, TR3, TR3A and TR3B
Required: 2
low note - reproduction of Lucas 9H windtone horn with two terminals. 12 volt
Plastic replacement for all original horns. Require mounting bracket 21074 (ill. 24)
Required: 1
high note - reproduction of Lucas 9H windtone horn with two terminals. 12 volt
Plastic replacement for all original horns. Require mounting bracket 21074 (ill. 24)
Required: 1
horn - supplied in pairs
For replacement horns 2820 and 2821 (ill. 23)
Required: 1
hydraulic, with screw-in terminals
TR2, TR3 to TS13045 - cars with Lockheed brakes
Required: 1
hydraulical, with lucar terminals - NPTF thread
TR2, TR3 to TS13045 - cars with Lockheed brakes
Required: 1
hydraulic, with lucar terminals
TR3 from TS13045, TR3A and TR3B, TR4 to CT26929 - cars with Girling brakes
Required: 1
mechanical
TR4 from CT26930, TR4A
- fixed at pedal box
Required: 1
brake light switch
TR4 from CT26930, TR4A
- fixed at pedal box
Required: 1
TR4 from CT26930, TR4A
- fixed at pedal box
Required: 1
6RA type with 4 Lucar terminals - overdrive, starter motor, ignition, horn, alternator and heater motor
Required: 1
6RA type with 4 Lucar terminals - overdrive, starter motor, ignition, horn, alternator and heater motor
TR4A (1965-67)
Required: 1
6RA type with 4 Lucar terminals - overdrive, starter motor, ignition, horn, alternator and heater motor
TR4A (1965-67)
Required: 1
for temperature gauge - electrical
TR4 and TR4A
Required: 1
headlamps - round FS22/1 type with screw-in terminals
TR2 and TR3, TR3A to TS60000
Required: 1
dip switch to bulkhead
TR2 from TS13046,TR3, TR3A to TS60000
Required: 2
headlamps - round 21SA type with screw terminals
TR3A from TS60001, TR3B and early TR4
Required: 1
dip switch to bulkhead
TR3A fromTS60001 and TR3B and also early TR4 RHD
Required: 2
dip switch to bracket
TR3A fromTS60001 and TR3B and also early TR4 LHD
Required: 2
TR3A fromTS60001 and TR3B and also early TR4 LHD
Required: 2
headlamps - square 103SA type with lucar terminals
Late TR4, TR4A
Required: 1
dip switch to bulkhead resp. to bracket
Late TR4, TR4A
Required: 2
dip switch - new item
TR4 and TR4A - LHD only
Required: 1
dip switch - used item
TR4 and TR4A - LHD only
Required: 1
12 volt, for positive and negative earthed cars without cut-off relay, complete with fitting instructions
Required: 1
