Wheel bearing and drive shaft

RH rear - feature: for Rover type axle with haf shaft with 10 splines, length: 67 cm

Series II and IIA (1958-71) plus 88" Series III to June 1980

RH rear - feature: for ENV type axle with haf shaft with 10 splines to inner end and 24 splines to outer end, overall length: 32.9"

Series II and IIA (1958-71)

RH rear - feature: for Salisbury type axle with haf shaft with 24 splines

88" Series III from July 1980

RH rear - feature: for Salisbury type axle with haf shaft with 24 splines

109" Series III (1971-85)

LH rear - feature: for Rover type axle with haf shaft with 10 splines, length: 88.8 cm

Series II and IIA (1958-71) plus 88" Series III to June 1980

LH rear - feature: for ENV type axle with haf shaft with 10 splines to inner end and 24 splines to outer end, overall length: 32.9"

Series II and IIA (1958-71)

LH rear - feature: for Salisbury type axle with haf shaft with 24 splines

88" Series III from July 1980

LH rear - feature: for Salisbury type axle with haf shaft with 24 splines

109" Series III (1971-85)

rear axle

Series II and IIA (1958-71) plus Series III to September 1980 except 109" 3.5 V8 models

rear axle

109 V8 models to September 1980

109 V8 models

rear axle

Series III including 3.5 V8 models from October 1980

axle casing

wheel bearing

Series II, IIA and early Series III 4- and 6-cylinder models (1958 to October 1980)

wheel bearing

Series III 4- and 6-cylinder models from October 1980 plus alle Series III V8 (1979-85)

wheel bearing

All models except 109 V8 to September 1980

rear suspension - inner bearing

Series II, IIA and early Series III 4- and 6-cylinder models (1958 to October 1980)

rear suspension - inner bearing

Series III 4- and 6-cylinder models from October 1980 plus alle Series III V8 (1979-85)

with wheel studs

Serie II, IIA and Serie III to September 1980 except 109 V8

Serie III from October 1980, 109 V8 all models

front and rear hub

front and rear suspension - outer bearing

Series II, IIA and early Series III 4- and 6-cylinder models (1958 to october 1980)

rear suspension - outer bearing

Series III 4- and 6-cylinder models from October 1980 plus alle Series III V8 (1979-85)

wheel bearing

- outer position

rear

Serie II, IIA Rover axle, Serie III 88 to Juni 1980

Identify by: 10 splines

rear

Serie II, IIA ENV axle

rear

Serie III 109 to September 1983, 88 Serie III from July 1980 to September 1983

rear

Serie III from October 1983 except 109 V8

retaining drive flange

Serie II, IIA Rover axle, Serie III 88 to Juni 1980

Serie II, IIA Rover axle, Serie III 88 to Juni 1980

Series II, IIA with Rover axle, Serie III 88 to Juni 1980

Serie II, IIA Rover-axle, Serie III 88 to Juni 1980

drive flange

Serie II, IIA ENV axle, Serie III 109 models and 88 models from July 1980 to September 1983

Serie II, IIA ENV axle, Serie III 109 models and 88 models from July 1980

rear hub

Serie III from October 1983

rear hub

All models from October 1983

with 9/16" BSF thread - screw in type

Series II all models and Series IIa to suffix "G"

with 9/16" BSF thread - press fit type

Series II and Series IIa to suffix "G"

with M16 x 1.5 thread and 41.8 mm total length - press fit type

Serie IIA from suffix "H" and Serie III

rear

Series II, IIA and early Series III 4- and 6-cylinder models (1958 to October 1980)

rear

Series III 4- and 6-cylinder models from October 1980 plus alle Series III V8 (1979-85)